邂逅一支烟 发表于 2013-10-31 22:40:14

典型性辊压模具车削程序

data/attachment/forum/20131031/164810s4jz51jpdg4bpbpd.jpg
data/attachment/forum/20131031/1648098p6nbpuuundssxjx.jpg
data/attachment/forum/20131031/164807n9anjzflw6a5njw4.jpg
data/attachment/forum/20131031/164608sj6u0l3vvp3olppo.jpg
data/attachment/forum/20131031/164611l2p22l2l5pvhzi8i.jpg
data/attachment/forum/20131031/164613s3zv2kkgqemr32ke.jpg
data/attachment/forum/20131031/1646162q2zowo2b2narg22.jpg
data/attachment/forum/20131031/164620jjbqkxj2azgwu7ew.jpg
data/attachment/forum/20131031/164623u1h5gab9e5q0dab9.jpg
data/attachment/forum/20131031/164627kjqwvlzgvwn1v0lx.jpg
data/attachment/forum/20131031/1646307bgnug4s27zzf7da.jpg
data/attachment/forum/20131031/164634c5cpf2i5jabs2jbi.jpg
data/attachment/forum/20131031/1646382u42onnbssb6n29r.jpg
data/attachment/forum/20131031/1646415jrj5rtalvltpzz7.jpg
data/attachment/forum/20131031/1646459jyyufyso0odpbf6.jpg
data/attachment/forum/20131031/1646521p565c15psss4csp.jpg
data/attachment/forum/20131031/1646581ttg8ghhzrepa1ig.jpg
data/attachment/forum/20131031/164706zmupqi9enpunopcz.jpg
data/attachment/forum/20131031/164709t4g0lggssz80sat8.jpg
data/attachment/forum/20131031/164712bod7r8o7esuj7ovu.jpg
data/attachment/forum/20131031/164717pcgz3zxawgpwx58b.jpg
data/attachment/forum/20131031/164723npoggcfa0htehfcc.jpg
data/attachment/forum/20131031/164727l7t3zixsm3hx2cx6.jpg
data/attachment/forum/20131031/164729r4wbkzwyrjrwharj.jpg
data/attachment/forum/20131031/164737o6iooc6f4vcm24ow.jpg
data/attachment/forum/20131031/1647421ouio4cquou0j5qi.jpg
data/attachment/forum/20131031/1647459z6wl9qv9yu89lt9.jpg
data/attachment/forum/20131031/1647523zzashhhynzmevq5.jpg
data/attachment/forum/20131031/164755xxqxofl5055xftbo.jpg
data/attachment/forum/20131031/1647591kp17qvjjpqsips1.jpg
data/attachment/forum/20131031/1648030y2cc6ybfcbjfmc7.jpg
data/attachment/forum/20131031/164806mm6zl4v4ls6zx6mx.jpg

邂逅一支烟 发表于 2013-10-31 22:41:07

凹弧先用车锥法,再用车弧法,一刀一刀车，没有循环,刀刀是节点.外径才用循环,凹弧车削前，先用切槽刀切一个槽,这样可以防止尖刀3边受力,造成扎刀

rlbb 发表于 2013-10-31 22:41:42

晕，看程序是个考验。

习惯风暴 发表于 2013-10-31 22:42:13

晕，看程序是个考验
缺失

onelee 发表于 2013-10-31 22:42:48

可以用G71的2型沟槽循环，方便很多

学徒abc 发表于 2013-10-31 22:43:31

楼主有图纸没有？是不是中间有个R的？我看到人家普车上干的。

学徒abc 发表于 2013-10-31 22:44:28

什么是G71的2型沟槽循环？980TDB支持吗？问师傅指教。

邂逅一支烟 发表于 2013-10-31 22:45:17


学徒abc 发表于 2011-8-1 10:53

楼主有图纸没有？是不是中间有个R的？我看到人家普车上干的。
这是3分之一弧，不是2分之一弧，而且上下 模具配合3丝，普车是做不出来的，也达不到光洁度的。而且成型刀也达不到弧度要求

邂逅一支烟 发表于 2013-10-31 22:45:49


学徒abc 发表于 2011-8-1 10:56

什么是G71的2型沟槽循环？980TDB支持吗？问师傅指教。
TDB可以支持2型G71

学徒abc 发表于 2013-10-31 22:46:40

楼主，那您是用什么刀干的啊？什么是G71的2型沟槽循环
页: [1]
查看完整版本: 典型性辊压模具车削程序